Перейти к основному содержимому

Using toncli

starter tip

If you didn't use toncli before, try QUICK START GUIDE.

Testing using toncli

toncli uses FunC to test smart contracts. Also, the latest version supports Docker for quick environment setup.

This tutorial will help you test the functions of our smart contract to make sure that the project is working correctly.

The best tutorial describing testing using toncli is:

FunC test structure under toncli

To test our smart contract, we will have to write 2 functions. One of which takes values, contains the desired result, gives an error if the function under test does not work correctly.

Let's create a file with tests

Create in the tests folder, the file example.func in which we will write our tests.

Data function

As a rule, the testing function does not accept arguments, but must return them.

  • function selector - id of the called function in the tested contract;
  • tuple - (stack) values ​​that we will pass to the function that performs tests;
  • c4 cell - "permanent data" in the control register c4;
  • c7 tuple - "temporary data" in the control register c7;
  • gas limit integer - gas limit (to understand the concept of gas, I advise you to first read about it in Ethereum);
About Gas

Gas is a value that shows how many resources a smart contract spends on its execution. Accordingly, the smaller it is, the better.

And you can read in detail here. Well, in full detail here in Appendix A.

More about registers c4 and c7 here in 1.3.1

Let's start writing tests for our smart contract

Introduction

In the new tests, testing occurs through two functions that allow you to call smart contract methods:

  • invoke_method, which assumes no exception will be thrown
  • invoke_method_expect_fail, which assumes an exception will be thrown

These are the functions inside the testing function, which can return any number of values, all of them will be displayed when the tests are run in the report.

Important!

It is worth noting that each test function name must begin with _test.

Creating a test function

Let's call our test function __test_example(), it will return the amount of gas consumed, so it will be int.

int __test_example() {

}

Register update c4

Since we will need to frequently update the c4 register due to a large number of tests, so we will create a helper function that will write c4 to zero

() set_default_initial_data() impure {
set_data(begin_cell().store_uint(0, 64).end_cell());
}
  • begin_cell() - will create a Builder for the future cell
  • store_uint() - writes the value of total
  • end_cell()- create Cell
  • set_data() - writes the cell to register c4

impure is a keyword that indicates that the function changes the smart contract data.

We got a function that we will use in the body of our testing function

Result:

int __test_example() {
set_default_initial_data();

}

Test Methods

It is worth noting that in the new version of the tests, we have the ability to call several smart contract methods in the testing function.

Inside our test, we will call the recv_internal() method and the Get method, so we will increment the value in c4 with the message and immediately check that the value has changed to the one sent.

To call the recv_internal() method, we need to create a cell with a message.

int __test_example() {
set_default_initial_data();
cell message = begin_cell().store_uint(10, 32).end_cell();
}

After this step, we are going to use the invoke_method method.

This method takes two arguments:

  • method name
  • arguments to test as a tuple

Two values ​​are returned: the gas used and the values ​​returned by the method (as a tuple).

It's worth noting

Two values ​​are returned: the gas used and the values ​​returned by the method (as a tuple).

In the first call, the arguments will be recv_internal and a tuple with a message transformed into a slice using begin_parse()

var (int gas_used1, _) = invoke_method(recv_internal, [message.begin_parse()]);

For the record, let's store the amount of gas used in int gas_used1.

In the second call, the arguments will be the Get method get_total() and an empty tuple.

var (int gas_used2, stack) = invoke_method(get_total, []);

For the report, we also store the amount of gas used in int gas_used2, plus the values ​​that the method returns, to check later that everything worked correctly.

We get:

int __test_example() {
set_default_initial_data();

cell message = begin_cell().store_uint(10, 32).end_cell();
var (int gas_used1, _) = invoke_method(recv_internal, [message.begin_parse()]);
var (int gas_used2, stack) = invoke_method(get_total, []);

}

Now, finally, the most important step. We have to check if our smart contract is working properly.

That is, if it returns the correct result, we return success or failure and the gas used.

[int total] = stack; 
throw_if(101, total != 10);

Explanations:

  • Passing a tuple
  • In the first argument, the number of the error (101), which we will receive if the smart contract does not work correctly
  • In the second argument is the correct answer
int __test_example() {
set_data(begin_cell().store_uint(0, 64).end_cell());
cell message = begin_cell().store_uint(10, 32).end_cell();
var (int gas_used1, _) = invoke_method(recv_internal, [message.begin_parse()]);
var (int gas_used2, stack) = invoke_method(get_total, []);
[int total] = stack;
throw_if(101, total != 10);
return gas_used1 + gas_used2;
}

This is the whole test, very convenient.